The tapered barrel on these bushings is split on both sides, permitting them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for use with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it in to the sprocket or pulley.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and can be purchased on the same page as the pulley you need. For apply with 5/8” shaft sizes. Includes set screws. Further Features: Manufactured from Steel For apply with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque ability from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and gear belt pulleys. The split tapered bushing alleviates the necessity to have an element bored to size, preferably lowering readily available requirements and enabling alterations in shaft size if necessary. The barrel of the split tapered bushing is certainly split in two locations and is usually keyed to the shaft. The barrel OD can be keyed to the travel component as well. The good thing about the split tapered bushing could it be will hold, regardless if the fasteners become loose. Split tapered bushings happen to be Split Taper Bushing china interchangeable between manufacturers.

Taper bushing are trusted as well as sprockets, v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are made of high quality engineered supplies with great tolerance. The feature is easy to work with and needs no further alteration. These bushings can fit almost all sorts of assemblies and sizes. They are the best choice in design for mechanical connections.
To complete designations add bore size. For example: PD1215X16MM designates a 1215 taper bushing with a 16mm bore.
No costly re-boring: total selection of both metric and imperial readily available.
Standard range suits up to 125mm/5″ shafts & Hub diameter required is determined by the application.
Complete brief reach range readily available, for compact lightweight assemblies & Clean, Compact Design.
Simple installation and removal.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and will be purchased on a single page as the pulley you need.
For use with 1 3/16” shaft sizes.
Comes with 2 set screws.

Additional Features:
Made of Steel
For use with cast iron bushed bore pulley
This U1 Bushing with 5-1/2″ bore is a high-quality precision product that’s built for strength and strength. U1 bushings are used in an extensively wide variety of applications, which include; sprockets, shaves, pulleys, gears, plus much more, we as well offer all of these products. What models this bushing apart may be the high-quality steel building along with exact manufacturing and high quality control; this means that you always get yourself a premium quality constant product. What really units us in addition to the other men is our experienced expert staff members and our company-wide goal of customer satisfaction.
1. Be sure the tapered cone floors of the bushing and the inside of the driven product will be clean and free of anti-seize lubricants.
2. Place the bushing in sprocket or various other component type that accepts the bushing.
3. Place cap screws loosely in pull-up holes. The bushing continues to be loose to assure sliding fit on shaft.
4. With essential on shaft, slide the sprocket or other component type to the desired posture on the shaft. Make sure to leave the heads of the cap screws attainable.
5. Align the sprocket or portion type, tighten the screws alternatively and progressively until they will be pulled up tight. Do not use extensions on the wrench handles and don’t allow the sprocket or portion to end up being drawn i contact with flange of bushing. At this time there should be a gap between the bushing flange and sprocket, make certain this gap does not close.
Dual split barrel ensures concentricity
Grips the shaft with great clamp fit
High torque carrying capacity
Permits blind assembly
Load not carried or tied to mounting screws
External key of all sizes for positive drive and better torque carrying capabilities
Double-split barrel for positive clamping
Solid flange to keep concentric bores
Available in inches, metric, and spline bores. Bore range from 3/8″ to 10″
Solid Flange & Dual Split Barrel – Assures better concentricity to the shaft.
Key to Key Travel – With keys on both shaft and product to provide the strongest possible drive.
3/4″ per Foot Taper on Barrel – Personal locking taper supplies the highest amount of mechanical locking merchandise to product.
The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for make use of with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it in to the sprocket or pulley.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and will be purchased on a single page as the pulley you will need. For make use of with 5/8” shaft sizes. Comes with set screws. Further Features: Made of Steel For employ with cast iron bushed bore pulley
Our stock steel Split Taper bushings feature wrench torque ability from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the necessity to have a component bored to size, ideally lowering on hand requirements and allowing for alterations in shaft size if important. The barrel of the split tapered bushing is split in two areas and is certainly keyed to the shaft. The barrel OD is also keyed to the travel component aswell. The good thing about the split tapered bushing is it will hold, whether or not the fasteners turn into loose. Split tapered bushings are interchangeable between manufacturers.